meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

indoor_monitor:feature_guides:c31x_it8x_auto_provisioning_parameter_list [2019/01/14 11:25] (current)
Line 1: Line 1:
 +======C31X&​IT8X auto provisioning parameter list======
 +
 +=====Introduction=====
 +====Auto-provision configuration format====
 +<ff sans-serif>​T<​fs medium>​here are 2 types of auto-provision configuration format, one is general configuration which not relate to any configuration files in device, the other one is normal configuration which relates to configuration files in device.
 +
 +For normal configurations</​fs></​ff>​ \\ 
 +{{ :​2.indoor_monitor:​feature_guides:​c1.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​①Config,​ the fixed prefix.\\ ​
 +②Settings,​ the module name of configuration,​ each module name relates to one configuration file in device. For example, Settings module relates to /​config/​Phone/​General/​Setting.conf.\\ ​
 +③④ LOGLEVEL.Level,​ The section and key name of this configuration.</​fs></​ff> ​
 +
 +===The mapping for module names and files===
 +^ Module Name  ^ File  ^
 +| Autoprovision ​ |/​config/​Network/​Autoprovision/​Autoprovision.conf ​ |
 +| Network |/​config/​Network/​General/​Network.conf ​ |
 +| Account1 ~ Account6 | /​config/​Network/​Sip/​SipAccount0.conf ~ /​config/​Network/​Sip/​SipAccount5.conf ​ |
 +| Voice  |/​config/​Voice/​Voice.conf ​  |
 +| Video  |/​config/​Voice/​Video.conf ​  |
 +| Forward ​ |/​config/​Phone/​Call/​Forward.conf ​  |
 +| BroadSoft ​  ​|/​config/​Phone/​Contact/​BroadSoft.conf ​  |
 +| Ldap  |/​config/​Phone/​Contact/​LDAP.conf ​  |
 +| RemotePhoneBook ​ |/​config/​Phone/​Contact/​RemotePhoneBook.conf ​  |
 +| AreaCode ​ |/​config/​Phone/​General/​DialRule/​AreaCode.conf ​  |
 +| Features ​  ​|/​config/​Phone/​General/​Features.conf ​  |
 +| Settings ​ |/​config/​Phone/​General/​Setting.conf ​  |
 +| DoorSetting ​  ​|/​config/​Door/​Setting.conf ​  |
 +| Programable ​ |/​config/​Phone/​Key/​ProgramableKey.conf ​ |
 +| Indoor |/​config/​Indoor/​General/​Setting.conf |
 +| HomeSecurity0 |/​config/​Phone/​General/​HomeSecurity0.conf|
 +
 +
 +
 +
 +=====General Configuration=====
 +====Firmware====
 +
 +<ff sans-serif><​fs medium>​1.Config.Firmware.Url=\\
 +*Description:​ The URL which firmware can be downloaded from. It supports FTP/​TFTP/​HTTP/​HTTPS protocol.The suffix of firmware should be .rom.\\ ​
 +*Example:​Config.Firmware.Url=http://​192.168.0.100/​IT80/​80.0.3.1.rom;</​fs></​ff>​
 +  ​
 +<​note>​NOTE:​ Device will reboot automatically after upgraded.</​note>​
 +\\ 
 +====Web Camera====
 +<ff sans-serif><​fs medium>​1.Config.WebCam.Url=\\
 +*Description:​ Configure the URL of the webcam file server, support ftp/​tftp/​http/​https protocol, the suffix of the file name must be .xml;​\\ ​
 +*Example:​Config.Webcam.Url=http://​192.168.0.100/​IT80/​monitor.xml ​
 +\\
 +*XML file format:</​fs></​ff> ​
 +{{ :​2.indoor_monitor:​feature_guides:​c3.png?​nolink |}}
 +
 +<fs medium><​ff sans-serif>​**Type**:​ Only support 1 currently.\\ ​
 +\\
 +**DeviceName**:​ The name of this device.\\ ​
 +\\
 +**Url**: The rtsp URL of this device, if user inputs IP address here, it will be transferred to Akuvox'​s RTSP URL format {{:​2.indoor_monitor:​feature_guides:​rtsp_stream.png?​nolink|}} \\
 +\\
 +**User**: The user name of RTSP URL.\\ ​
 +\\
 +**Password**:​ The password of RTSP URL.</​ff> ​
 +</fs> \\
 +\\ 
 +<ff sans-serif><​fs medium>​**Website**:​Phone->​Monitor</​fs></​ff>​ \\ 
 +{{ :​2.indoor_monitor:​feature_guides:​c2.png?​nolink |}}
 +<​note>​Device will reboot automatically after updated client certificate.</​note>​
 +\\ 
 +\\ 
 +
 +
 +
 +
 +
 +==== Client Certificate ====
 +
 +<ff sans-serif><​fs medium>​1. Config.Certificate.01.Url-Config.Certificate.10.Url=\\
 +*Description:​ Configure the URL of client certificate,​ support up to 10 URLs.This client certificate is used for SIP TLS, HTTPS download, VPN, etc.\\
 +*File Format: .crt or .pem file.\\
 +*Example:</​fs></​ff>​
 +   ​Config.Certificate.01.Url = tftp://​192.168.0.100/​Akuvox-CA.crt
 +
 +<​note>​Device will reboot automatically after updated client certificate.</​note>​
 +
 +=====Android Devices=====
 +
 +====Contact====
 +<ff sans-serif><​fs medium>​1. Config.Contact.Url =\\ 
 +*Description:​ Configure the URL of the contact file, the suffix of the file name must be .xml/​.csv/​.vcf and .zip.\\ ​
 +It supports ftp/​tftp/​http/​https protocol.\\
 +\\
 +*Example:</​fs></​ff>​
 +   ​Config.Contact.Url = tftp://​192.168.0.100/​Akuvox-contact.xml ​
 +<ff sans-serif><​fs medium>​2. Config.Contact.Mode =0\\ 
 +*Description:​ Configure the mode for importing the contact file downloaded.</​fs></​ff>​ \\
 +<ff sans-serif><​fs medium>​*Value:</​fs></​ff>​\\
 +^Value ​  ​^Description ​  ^
 +|0(default) ​  ​|Append contacts ​  |
 +|1  |Replace contacts ​  |
 +
 +====Android Application=====
 +<​file>​
 +Config.Add.Application.Url =
 +Config.Add.Application.01.Url =
 +Config.Add.Application.02.Url =
 +Config.Add.Application.03.Url =
 +Config.Add.Application.04.Url =
 +Config.Add.Application.05.Url =
 +Config.Add.Application.06.Url =
 +Config.Add.Application.07.Url =
 +Config.Add.Application.08.Url =
 +Config.Add.Application.09.Url =
 +Description:​ Configure the URL of apk which would be installed.
 +
 +Config.Update.Application.Url =
 +Config.Update.Application.01.Url =
 +Config.Update.Application.02.Url =
 +Config.Update.Application.03.Url =
 +Config.Update.Application.04.Url =
 +Config.Update.Application.05.Url =
 +Config.Update.Application.06.Url =
 +Config.Update.Application.07.Url =
 +Config.Update.Application.08.Url =
 +Config.Update.Application.09.Url =
 +Description:​ Configure the URL of apk which would be updated.
 +
 +Config.Del.Application.Url =
 +Config.Del.Application.01.Url =
 +Config.Del.Application.02.Url =
 +Config.Del.Application.03.Url =
 +Config.Del.Application.04.Url =
 +Config.Del.Application.05.Url =
 +Config.Del.Application.06.Url =
 +Config.Del.Application.07.Url =
 +Config.Del.Application.08.Url =
 +Config.Del.Application.09.Url =
 +Description:​ Configure the URL of apk which would be removed.
 +</​file>​
 +
 +====Android Settings====
 +<ff sans-serif><​fs medium>​1. Config.Autoprovison.RESET_FACTORY.Enable =\\ 
 +*Description:​ Enable/​Disable resetting to factory settings after auto-provisioning.\\</​fs></​ff> ​
 +
 +<ff sans-serif><​fs medium>​2. Config.Autoprovision.RESET_FACTORY.SaveMode =\\ 
 +*Description:​ Save mode, which would be used when resetting to factory settings is enabled.\\</​fs></​ff> ​
 +<ff sans-serif><​fs medium>​*Value:</​fs></​ff>​\\ ​
 +^Value^Description^
 +|1|Save configurations of device only.|
 +|2|Save configurations of phone and contacts.|
 +|3|Save contacts only.|
 +|4|Save generic and MAC configurations of auto-provisioning.|
 +|0 or others|Don'​t save anything.|
 +
 +<ff sans-serif><​fs medium>​3. Config.Autoprovision.Reboot.Enable=0\\ ​
 +*Description:​ Enable/​Disable rebooting after auto-provisioning.</​fs></​ff>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​4. Config.Android.Launcher.PermissionLevel=\\ ​
 +*Android Launcher permission level.</​fs></​ff>​\\ ​
 +<ff sans-serif><​fs medium>​*Value:</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|1 |User|
 +|2 |Admin|
 +|3 |Master|
 +|Others |Invalid.|
 +
 +<ff sans-serif><​fs medium>​5. Config.Android.Launcher.MasterPwd= \\ 
 +\\
 +6. Config.Android.Launcher.AdminPwd= \\ 
 +*Description:​ The password for Master/​Admin.\\ ​
 +\\
 +7. Config.System.Setting.Pwd =\\ 
 +*Description:​ The password for android advanced setting.\\</​fs></​ff>  ​
 +<​note>​NOTE:​ The password would be cleared if the value is empty.</​note>​
 +
 +=====Auto-provisioning=====
 +====General====
 +<ff sans-serif><​fs medium>​1. Config.Autoprovision.GENERAL.Url=\\ ​
 +*Description:​ The URL which device will download provisioning file from.\\ ​
 +\\
 +2. Config.Autoprovision.GENERAL.UserName=\\ ​
 +*Description:​ The user name for the URL which device will download provisioning file from.\\ ​
 +\\
 +3. Config.Autoprovision.GENERAL.Pwd=\\ ​
 +*Description:​ The password for the URL which device will download provisioning file from.\\ ​
 +
 +4. Config.Autoprovision.GENERAL.CustomEnable=0\\ ​
 +*Description:​ The provisioning file is customized or not.\\</​fs></​ff> ​
 +<fs medium><​ff sans-serif>​*Value:</​ff></​fs>​\\ ​
 +^Value ^Description^
 +|0(default) |Not customized, the suffix of provisioning file should be .cfg.|
 +|1 |Customized,​ all provisioning files are supported.|
 +
 +
 +====Schedule====
 +<ff sans-serif><​fs medium>​5. Config.Autoprovision.SCHEDULE.DayOfWeek=7\\ ​
 +*Description:​The week day on which auto-provisioning would be done. It supports only single day.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Every day.|
 +|1~7 |1=Monday,​ 2=Tuesday,​... ,7=Sunday.|
 +|8 |Use Config.Autoprovision.SCHEDULE.SomeDayOfWeek instead.|
 +
 +<ff sans-serif><​fs medium>​*Website:​\\
 +Upgrade->​Advanced->​Automatic Autop</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c4.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​6. Config.Autoprovision.SCHEDULE.SomeDayOfWeek=7\\ ​
 +*Description:​The week days on which auto-provisioning would be done. It supports multiple week days, separated by comma (,) symbol.\\ ​
 +*Website:\\
 +Upgrade->​Advanced->​Automatic Autop</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c5.png?​nolink |}}
 +<ff sans-serif><​fs medium>​*Example:</​fs></​ff> ​
 +<​file>​
 +Config.Autoprovision.SCHEDULE.SomeDayOfWeek=1,​2,​7 ​
 +means auto-provisioning will be done at Monday, Tuesday and Sunday. 1=Monday, 2=Tuesday,​... ,7=Sunday.
 +</​file>​
 +
 +<ff sans-serif><​fs medium>​7. Config.Autoprovision.SCHEDULE.HourOfDay=22\\ ​
 +\\
 +8. Config.Autoprovision.SCHEDULE.MinuteOfHour=0\\ ​
 +\\
 +9. Config.Autoprovision.SCHEDULE.SecondOfMinute=0\\ ​
 +*Description:​ The Hour/​Minute/​Second on which auto-provisioning would be done.\\ ​
 +*Website:</​fs></​ff>​ \\
 +{{ :​2.indoor_monitor:​feature_guides:​c6.png?​nolink |}}
 +
 +====Others====
 +<ff sans-serif><​fs medium>​10. Config.Autoprovision.MODE.Mode\\ ​
 +*Description:​Auto-provisioning mode.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disable.|
 +|1(default) |Power On, do provisioning when system powered on.|
 +|2 |Repeatedly,​ do provisioning at the time be set on Schedule section.|
 +|3 |Power On + Repeatedly.|
 +|4 |Hourly Repeat, do provisioning for each hour.|
 +
 +<ff sans-serif><​fs medium>​Website:</​fs></​ff>​\\ ​
 +{{ :​2.indoor_monitor:​feature_guides:​c7.png?​nolink |}}
 +<ff sans-serif><​fs medium>​11. Config.Autoprovision.AES.Key16=\\ ​
 +\\
 +12. Config.Autoprovision.AES.Key16Mac=\\ ​
 +*Description:​AES key for decrypting the provisioning template file downloaded from file server, Key16 is for r00000000xx.cfg,​ and Key16Mac is for <​MAC>​.cfg.\\
 +*Example:</​fs></​ff>​\\ ​
 +
 +<​file>​
 +Config.Autoprovision.AES.Key16 = Aku.123@test
 +Config.Autoprovision.AES.Key16Mac = Aku.456@test</​file>​
 +
 +<ff sans-serif><​fs medium>​Website:</​fs></​ff>​\\ ​
 +{{ :​2.indoor_monitor:​feature_guides:​c8.png?​nolink |}}
 +<​note>​NOTE:​ You can use Akuvox AES Tool to encrypt the provisioning template file firstly if you set key for the 2 configurations.</​note>​
 +
 +<ff sans-serif><​fs medium>​13. Config.Autoprovision.PNP.Enable=0\\ ​
 +*Description:​Enable/​Disable PNP Auto-provisioning.</​fs></​ff>​\\
 +^Value ^Description^
 +|0 (default) |Disable|
 +|1 |Enable|
 +
 +<ff sans-serif><​fs medium>​Website:</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c9.png?​nolink |}}
 +\\ 
 +<fs medium><​ff sans-serif>​14. Config.Autoprovision.RETRY_TIMES.Times=0\\ ​
 +*Description:​ How many times auto-provisioning would be tried if the provisioning file downloaded failed.</​ff></​fs>​\\
 +
 +=====Network=====
 +====LAN Port====
 +<ff sans-serif><​fs medium>​15. Config.Network.LAN.Type = 0\\ 
 +*Description:​ Network type of LAN.</​fs></​ff>​\\
 +^Value ^Description^
 +|0 (default) |DHCP|
 +|1 |PPPoE|
 +|2 |Static IP address|
 +<ff sans-serif><​fs medium>​16. Config.Network.LAN.StaticIP = \\ 
 +\\
 +17. Config.Network.LAN.SubnetMask =\\ 
 +\\
 +18. Config.Network.LAN.DefaultGateway = \\ 
 +\\
 +19. Config.Network.LAN.PrimaryDNS = \\ 
 +\\
 +20. Config.Network.LAN.SecondaryDNS =\\ 
 +*Description:​ Static IP address/​Subnet Mask/​Gateway/​Primary DNS/​Secondary DNS, it will be activated when Config.Network.LAN.Type=2.\\ ​
 +*Website: Network->​Basic->​LAN Port</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c10.png?​nolink |}}
 +
 +<ff sans-serif><​fs medium>​21. Config.Network.LAN.DHCP_VCI = udhcp 0.9.8\\ ​
 +*Description:​DHCP_VENDOR string in DHCP options. Default is udhcp 0.9.8\\
 +
 +22. Config.Network.LAN.LINK_TYPE = 0 \\ 
 +*Description:​Use Ethernet or WiFi.</​fs></​ff>​\\
 +^Value ^Description^
 +|0 (default) |Use Ethernet.|
 +|1 |Use WiFi.|
 +
 +
 +====PC Port====
 +<ff sans-serif><​fs medium>​23. Config.Network.PC.Type = 0\\
 +*Description:​ PC port would be use as bridge or router.</​fs></​ff>​\\
 +^Value ^Description^
 +|0 (default) |Router|
 +|1 |Bridge|
 +
 +<ff sans-serif><​fs medium>​24. Config.Network.PC.RouterIP = 10.0.0.1\\ ​
 +*Description:​ The router IP address, it will be activated when Config.Network.PC.Type = 0.\\
 +
 +25. Config.Network.PC.SubnetMask = 255.255.255.0\\ ​
 +*Description:​The subnet mask of router, it will be activated when Config.Network.PC.Type = 0.\\
 +
 +26. Config.Network.PC.EnableDHCP = 1\\ 
 +*Description:​ Enable/​Disbale DHCP server for router, it will be activated when Config.Network.PC.Type = 0.</​fs></​ff>​\\
 +^Value ^Description^
 +|0 |Disable DHCP server.|
 +|1(default) |Enable DHCP server.|
 +
 +<ff sans-serif><​fs medium>​27. Config.Network.PC.StartIP = 10.0.0.10\\ ​
 +*Description:​ The DHCP start IP address for router, it will be activated when Config.Network.PC.Type = 0 and Config.Network.PC.EnableDHCP = 1.\\
 +\\
 +28. Config.Network.PC.EndIP = 10.0.0.100\\
 +*Description:​ The DHCP end IP address for router, it will be activated when Config.Network.PC.Type = 0 and Config.Network.PC.EnableDHCP = 1.</​fs></​ff>​\\
 +
 +
 +====Others====
 +<ff sans-serif><​fs medium>​29. Config.Network.RTPPORT.Max = 12000\\ ​
 +*Description:​The Maximum of RTP port for SIP call. Default is 12000. Value range is 1024~65534. It should larger than Config.Network.RTPPORT.Min.\\ ​
 +*Website: Network->​Advanced->​Local RTP</​fs></​ff>​\\
 +{{ :​2.indoor_monitor:​feature_guides:​c11.png?​nolink |}}\\ 
 +<ff sans-serif><​fs medium>​30. Config.Network.RTPPORT.Min = 11800\\ ​
 +*Description:​The Minimum of RTP port for SIP call. Default is 11800. Value range is 1024~65534. It should smaller than Config.Network.RTPPORT.Max.</​fs></​ff>​\\ ​
 +
 +=====SIP Account=====
 +<​note>​NOTE:​ Account1 is for the first account, you can also configure Account2, Account3, etc</​note>​
 +
 +====SIP Server====
 +<ff sans-serif><​fs medium>​1. Config.Account1.GENERAL.Enable = 0\\ 
 +*Description:​Enable/​Disable this account.</​fs></​ff>​
 +
 +^Value ^Description^
 +|0 (default) |Disable|
 +|1 |Enable|
 +
 +<fs medium><​ff sans-serif>​2. Config.Account1.GENERAL.Label = \\ 
 +*Description:​ The label of this account, which would be displayed for users.</​ff></​fs>​\\
 +\\
 +<fs medium><​ff sans-serif>​3. Config.Account1.GENERAL.DisplayName = \\ 
 +*Description:​ The display name of this account, which would be displayed on remote party in a call. It would be included in SIP INVITE.\\
 +\\
 +4. Config.Account1.GENERAL.UserName = \\ 
 +*Description:​ The user name of this account, it would be provided by SIP server.\\
 +\\
 +5. Config.Account1.GENERAL.AuthName = \\ 
 +*Description:​ The authorization/​register name of this account, it would be provided by SIP server.\\ ​
 +\\
 +6. Config.Account1.GENERAL.Pwd = \\ 
 +*Description:​ The password of this account, it would be provided by SIP server.\\  ​
 +\\
 +7. Config.Account1.GENERAL.UserAgent = \\ 
 +*Description:​ The user agent for this account. It would be included in SIP header.\\ ​
 +\\
 +8. Config.Account1.SIP.Server = \\ 
 +*Description:​ The IP address or domain name of the primary SIP server.\\ ​
 +\\
 +9. Config.Account1.SIP.Server2 = \\ 
 +*Description:​ The IP address or domain name of the secondary SIP server.\\ ​
 +\\
 +10. Config.Account1.SIP.Port = 5060\\ ​
 +*Description:​ The port of the primary SIP server.\\ ​
 +\\
 +11. Config.Account1.SIP.Port2 = 5060\\ ​
 +*Description:​ The port of the secondary SIP server.\\ ​
 +\\
 +12. Config.Account1.SIP.TransType = 0\\ 
 +*Description:​ The transport type of the secondary SIP server.</​ff></​fs>​\\ ​
 +^Value ^Description^
 +|0 (default) |UDP|
 +|1 |TCP|
 +|2 |TLS|
 +
 +<ff sans-serif><​fs medium>​13. Config.Account1.SIP.ListenPortMin = 5062\\ ​
 +*Description:​ The maximum local SIP listening port. Value range is 1024-65534. It should be equal or smaller than Config.Account1.SIP.ListenPortMax.\\  ​
 +\\
 +14. Config.Account1.SIP.ListenPortMax = 5062\\ ​
 +*Description:​ The minimum local SIP listening port. Value range is 1024-65534. It should be equal or larger than Config.Account1.SIP.ListenPortMax</​fs></​ff>​.\\  ​
 +<​note>​NOTE:​ The local SIP listening port would be random in range of 
 +Config.Account1.SIP.ListenPortMin ~ Config.Account1.SIP.ListenPortMax.</​note>​\\ ​
 +
 +<ff sans-serif><​fs medium>​15. Config.Account1.REG.Timeout = 1800\\ ​
 +*Description:​ The SIP registering period for primary server. Value range is 30~65535.\\
 +\\
 +16. Config.Account1.REG.Timeout2 = 1800\\ ​
 +*Description:​ The SIP registering period for secondary server. Value range is 30~65535.\\
 +\\
 +17. Config.Account1.OUTPROXY.Enable = 0\\
 +*Description:​ Enable/​Disable outbound proxy server.\\
 +*Website: Account->​Basic->​Outbound Proxy Server</​fs></​ff>​\\
 +
 +{{ :​2.indoor_monitor:​feature_guides:​c12.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​18. Config.Account1.OUTPROXY.Server = \\ 
 +\\
 +19. Config.Account1.OUTPROXY.Port = 5060\\ ​
 +*Description:​ The primary outbound proxy server address and port. It would e activated when Config.Account1.OUTPROXY.Enable=1.\\ ​
 +*Website, Account->​Basic->​Outbound Proxy Server</​fs></​ff>​\\
 +{{ :​2.indoor_monitor:​feature_guides:​c13.png?​nolink |}}\\ 
 +<ff sans-serif><​fs medium>​20. Config.Account1.OUTPROXY.BakServer = \\ 
 +\\
 +21. Config.Account1.OUTPROXY.BakPort = 5060\\ ​
 +*Description:​ The secondary outbound proxy server address and port. It would e activated when Config.Account1.OUTPROXY.Enable=1.\\ ​
 +*Website, Account->​Basic->​Outbound Proxy Server</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c14.png?​nolink |}}\\ 
 +\\
 +<ff sans-serif><​fs medium>​22. Config.Account1.STUN.Enable = 0\\ 
 +*Description:​ Enable/​Disable STUN server for SIP account.\\ ​
 +\\
 +23. Config.Account1.STUN.Server = \\ 
 +*Description:​ The STUN server IP address or domain name. It would e activated when Config.Account1.STUN.Enable =1.\\ 
 +\\
 +24. Config.Account1.STUN.Port = 3478\\
 +*Description:​ The STUN server port. It would e activated when Config.Account1.STUN.Enable =1.</​fs></​ff>​ \\
 +
 +====DTMF====
 +<ff sans-serif><​fs medium>​25. Config.Account1.DTMF.Type = 2\\ 
 +*Description:​ The DTMF type for this SIP account</​fs></​ff>​.\\
 +^ Value       ^ Description ​        ^
 +| 0           | Invalid ​            |
 +| 1           | In-band ​            |
 +| 2(default) ​ | RFC2833 ​            |
 +| 3           | SIP INFO            |
 +| 4           | INBAND + SIP INFO   |
 +| 5           | RFC2833 + SIP INFO  |
 +<ff sans-serif><​fs medium>​*Website:​ Account->​Advanced->​DTMF</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c15.png?​nolink |}}\\ 
 +
 +<fs medium><​ff sans-serif>​26. Config.Account1.DTMF.Payload = 101\\ 
 +*Description:​ The DTMF payload type for RFC2833.</​ff></​fs>​\\ ​
 +
 +<ff sans-serif><​fs medium>​27. Config.Account1.DTMF.InfoType = 0\\ 
 +*Description:​ The DTMF SIP INFO type for this SIP account.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Invalid|
 +|1 |DTMF|
 +|2 |DTMF-Relay|
 +|3 |Telephone-Event|
 +
 +<ff sans-serif><​fs medium>​28. Config.Account1.DTMF.Duration = 300\\ 
 +*Description:​ The duration of DTMF. It would be used for In-band, RFC2833, SIP INFO(DTMF-Relay,​ Telephone-Event).\\ ​
 +\\
 +29. Config.Account1.DTMF.Power = \\
 +*Description:​ The Power of DTMF. It would be used for In-band, SIP INFO(Telephone-Event).</​fs></​ff>​\\
 +
 +====NAT====
 +
 +<ff sans-serif><​fs medium>​30. Config.Account1.NAT.UdpKeepEnable = 1\\ 
 +*Description:​ Enable/​Disable UDP keep alive feature.\\ ​
 +\\
 +31. Config.Account1.NAT.UdpKeepInterval = 30\\ 
 +*Description:​ The interval for UDP keep alive feature.\\ ​
 +
 +32. Config.Account1.NAT.Rport = 0\\ 
 +*Description:​ Enable/​Disable the RPORT feature for this SIP account.\\ ​
 +*Website: **Account->​Advanced->​NAT**</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c16.png?​nolink |}}
 +
 +====Audio & Video====
 +
 +<ff sans-serif><​fs medium>​33. Config.Account1.Video00.Enable = 1\\ 
 +*Description:​ Enable/​Disable video codec for this SIP account.\\ ​
 +
 +34. Config.Account1.Video00.Name = H264\\ ​
 +*Description:​ The name for this video codec.</​fs></​ff>​\\ ​
 +<​note>​NOTE:​ Only H264 video codec be supported on C313/​IT80/​IT81 currently.</​note>​
 +
 +<ff sans-serif><​fs medium>​35. Config.Account1.Video00.Priority = 2\\ 
 +*Description:​ The priority for this video codec. The value range is 0~10, 10 is the highest priority.\\ ​
 +\\
 +36. Config.Account1.Video00.Payload = 104\\ 
 +*Description:​ The payload type for this video codec.\\ ​
 +\\
 +37. Config.Account1.Video00.ProfileLevel = 3\\ 
 +*Description:​ The resolution for this video codec</​fs></​ff>​\\
 +^Value ^Description^
 +|0 |QCIF|
 +|1 |CIF|
 +|2 |VGA|
 +|3 (default) |4CIF|
 +|4 |720P|
 +|5 |QVGA|
 +
 +<ff sans-serif><​fs medium>​38. Config.Account1.Video00.PacketizationMode = 0\\ 
 +*Description:​ The packetization mode for this video codec</​fs></​ff>​\\
 +^Value ^Description^
 +|0 (default) |NALU|
 +|1 |STAP|
 +|2 |FU-A|
 +<​note>​NOTE:​ For C313/​IT80/​IT81,​ only FU-A mode is supported by Hw Encode Acceleration.</​note>​\\ ​
 +
 +<fs medium><​ff sans-serif>​39. Config.Account1.Video00.MaxBR = 2048\\ ​
 +*Description:​ The maximum bit rate for this video codec, the value range is 128~4096. The unit of it is kbps.</​ff></​fs>​\\ ​
 +
 +====Call====
 +
 +<ff sans-serif><​fs medium>​40. Config.Account1.CALL.PreventSIPHacking = 0\\ 
 +*Description:​ Enable/​Disable preventing SIP hacking feature.\\ ​
 +*Website: Account->​Advanced->​Call</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c17.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​41. Config.Account1.AUTO_ANSWER.Enable = 0\\ 
 +*Description:​ Enable/​Disable auto-answer for this SIP account.\\ ​
 +*Website: Account->​Advanced->​Call</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c18.png?​nolink |}}\\ 
 +
 +
 +=====Call & Intercom features=====
 +====CallWating & DND====
 +<ff sans-serif><​fs medium>​1. Config.Features.CALL_WAITING.Enable = 1\\ 
 +*Description:​ Enable/​Disable call waiting feature.\\ ​
 +\\
 +2. Config.Features.CALL_WAITING.PlayTone = 1\\ 
 +*Description:​ Enable/​Disable playing call waiting tone when there is a new incoming call waiting.\\ ​
 +
 +3. Config.Features.CALL_WAITING.OnCode = \\ 
 +\\*Description:​ The code would be called to server when user want to enable call waiting feature on SIP server.\\ ​
 +\\
 +4. Config.Features.CALL_WAITING.OffCode = \\ 
 +*Description:​ The code would be called to server when user want to disable call waiting feature on SIP server.</​fs></​ff>​\\ ​
 +<​note>​NOTE:​ If call waiting feature is enabled on SIP server, the new incoming call would not be sent to device, so device doesn'​t need to enable the call waiting feature.</​note>​
 +
 +<ff sans-serif><​fs medium>​5. Config.Features.DND.Status = 0\\ 
 +*Description:​ Enable/​Disable playing call waiting tone when there is a new incoming call waiting.\\ ​
 +*Website: Phone->​Call Feature->​DND</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c19.png?​nolink |}}
 +
 +<ff sans-serif>​6<​fs medium>. Config.Features.DND.ScheduleMode = 1\\ 
 +*Description:​ Enable/​Disable DND schedule mode.</​fs></​ff>​ \\ 
 +^Value ^Description^
 +|0 |Schedule mode, the DND feature will be activated between start time and end time.|
 +|1(default) |Whole day mode, the DND feature will be activated all the day.|
 +
 +7. Config.Features.DND.StartTime = 00:​00\\ ​
 +*Description:​ The start time which DND feature would be activated.\\ ​
 +
 +8. Config.Features.DND.EndTime = 00:​00\\ ​
 +/​Description:​ The start time which DND feature would be activated.\\
 +<​note>​NOTE:​ the DND feature would be activated if start time and end time are be set to 00:​00.</​note>​
 +
 +<ff sans-serif><​fs medium>​9. Config.Features.DNDMODE.IvrEnable = 0\\ 
 +*Description:​ Enable/​Disable playing IVR when DND is on.\\
 +\\
 +10. Config.Features.DNDMODE.DndExceptDoor = 0\\ 
 +*Description:​ Enable/​Disable accepting door phone to call in when device is in DND mode.</​fs></​ff>​\\ ​
 +\\
 +====Call====
 +
 +<ff sans-serif><​fs medium>​11. Config.Features.VIDEO_CODEC_PARAM.PacketizationMode = 0\\ 
 +*Description:​ The packetization mode for video codec of DIRECT IP call</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |NALU|
 +|1 |STAP|
 +|2 |FU-A|
 +
 +<​note>​NOTE:​ For C313/​IT80/​IT81,​ only FU-A mode is supported by Hw Encode Acceleration.</​note>​
 +
 +<ff sans-serif><​fs medium>​12. Config.Features.VIDEO_CODEC_PARAM.ProfileLevel = 4CIF\\ ​
 +*Description:​ The resolution for the video codec of DIRECT IP call</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |QCIF|
 +|1 |CIF|
 +|2 |VGA|
 +|3 (default) |4CIF|
 +|4 |720P|
 +|5 |QVGA|
 +
 +<ff sans-serif><​fs medium>​13. Config.Features.CALLROBIN.Num01 = \\ 
 +\\
 +14. Config.Features.CALLROBIN.Num02 = \\ 
 +\\
 +15. Config.Features.CALLROBIN.Num03 = \\ 
 +*Description:​ The first/​secondary/​thirdly number of robin call number list. Robin call is call the number in list one by one, it means that device would call the next number if current call was not answered by remote party.\\ ​
 +*Website: Phone->​Intercom->​SOS</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c20.png?​nolink |}}
 +
 +<ff sans-serif><​fs medium>​16. Config.Features.CALLROBIN.Time = 5 </​fs></​ff>​\\ ​
 +<ff sans-serif><​fs medium>​*Description:​ Device would call next number if the remote party didn't answer this call in some seconds. The range is 5-60.</​fs></​ff>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​17. Config.Features.CALLROBIN.Count = 2\\ 
 +*Description:​ How many times device would repeat to call the number in list. The range is 1~ 65535.</​fs></​ff>​\\ ​
 +\\
 +<fs medium><​ff sans-serif>​18. Config.Features.VOICE_OWNER.Enable = 0\\ 
 +*Description:​ Enable/​Disable owner'​s voice message. If the setting is enabled, the visitor would heard the voice message owner left when the call was not answered.</​ff></​fs>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​19. Config.Features.VOICE_OWNER.TimeOut = 0\\ 
 +*Description:​ Call in timeout for playing owner'​s voice message(IVR) for visitor. Value range is 0~60.</​fs></​ff>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​20. Config.Features.VOICE_VISITOR.Enable = 0\\ 
 +*Description:​ Enable/​Disable visitor'​s voice message, if this feature is enabled, visitor can leave voice message for owner if owner didn't answer the call.</​fs></​ff>​ \\
 +\\
 +
 +==== IP Paging ====
 +\\
 +
 +<ff sans-serif><​fs medium>​1. Config.Multicast.PRIORITY.Enable = 1\\ 
 +*Description:​ Enable/​Disable multicast call priority.\\
 +\\
 +2. Config.Multicast.PRIORITY.Priority = 0\\ 
 +*Description:​ The multicast call priority. 0 is the highest priority. The priority of SIP call is 0. If the priority of new multicast call is higher than current multicast call, current multicast call would be hold, and the new multicast call would be answered automatically.\\ ​
 +\\
 +3. Config.Multicast.GENERAL.Codec = 0\\ 
 +*Description:​ The payload type of multicast call's codec, 0 is for PCMU, 8 is for PCMA, 9 is for G.722, 18 is for G.729.\\ ​
 +\\
 +4. Config.Multicast.LISTEN0.Label = \\ 
 +\\
 +5. Config.Multicast.LISTEN0.IP = \\ 
 +\\
 +6. Config.Multicast.LISTEN1.Label = \\ 
 +\\
 +7. Config.Multicast.LISTEN1.IP = \\ 
 +\\
 +8. Config.Multicast.LISTEN2.Label = \\
 +\\
 +9. Config.Multicast.LISTEN2.IP = \\ 
 +\\
 +10. Config.Multicast.LISTEN3.Label = \\ 
 +\\
 +11. Config.Multicast.LISTEN3.IP = \\ 
 +\\
 +12. Config.Multicast.LISTEN4.Label = \\ 
 +\\
 +13. Config.Multicast.LISTEN4.IP = \\ 
 +\\
 +14. Config.Multicast.LISTEN5.Label = \\ 
 +\\
 +15. Config.Multicast.LISTEN5.IP = \\ 
 +\\
 +16. Config.Multicast.LISTEN6.Label = \\ 
 +\\
 +17. Config.Multicast.LISTEN6.IP = \\ 
 +\\
 +18. Config.Multicast.LISTEN7.Label =  \\ 
 +\\
 +19. Config.Multicast.LISTEN7.IP =  \\ 
 +\\
 +20. Config.Multicast.LISTEN8.Label =  \\ 
 +\\
 +21. Config.Multicast.LISTEN8.IP =  \\ 
 +\\
 +22. Config.Multicast.LISTEN9.Label =  \\ 
 +\\
 +23. Config.Multicast.LISTEN9.IP =  \\ 
 +*Description:​ Label is the display name for this multicast address. IP is the multicast IP and port, for example 238.8.8.11:​5000.\\ ​
 +*Website: Phone->​Multicast->​Listen List</​fs></​ff>​\\
 +{{ :​2.indoor_monitor:​feature_guides:​c21.png?​nolink |}}
 +
 +<ff sans-serif><​fs medium>​24. Config.Multicast.SELECTEDGROUP.SelectedGroup = 0 \\
 +*Description:​ Which multicast group address would be calling out. Value range is 1~3. For example, device would call out Config.Multicast.GROUP1.IP when Config.Multicast.SELECTEDGROUP.SelectedGroup = 1\\
 +*Website: Phone->​Multicast->​Multicast Setting</​fs></​ff>​\\
 +{{ :​2.indoor_monitor:​feature_guides:​c22.png?​nolink |}}
 +
 +<fs medium><​ff sans-serif>​25. Config.Multicast.GROUP1.IP = 224.1.6.11:​51230\\ ​
 +\\
 +26. Config.Multicast.GROUP2.IP = 224.1.6.11:​51231\\ ​
 +\\
 +27. Config.Multicast.GROUP3.IP = 224.1.6.11:​51232\\ ​
 +*Description:​ The multicast group address for calling out.\\
 +*Website: Phone->​Multicast->​Multicast List</​ff></​fs>​
 +{{ :​2.indoor_monitor:​feature_guides:​c23.png?​nolink |}} 
 +
 +
 +====Others====
 +<ff sans-serif><​fs medium>​1. Config.Features.SIPCONFIG.DirectIPUserAgent = Akuvox\\ ​
 +*Description:​ The SIP user agent for DIRECT IP Call.\\
 +\\
 +2. Config.Features.ACTIONURL.Enable = 0\\ 
 +*Description:​ Enable/​Disable action URL.</​fs></​ff>​\\
 +
 +
 +=====Settings=====
 +====Language====
 +<ff sans-serif><​fs medium>​1. Config.Settings.LANGUAGE.Type = 0\\ 
 +*Description:​ The language of device.</​fs></​ff>​
 +^Value ^Description^
 +|0(default) |English|
 +
 +<ff sans-serif><​fs medium>​Website:​ Phone->​Time/​Lang->​LCD Language</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c24.png?​nolink |}}
 +<​note>​NOTE:​ C313/​IT80/​IT81 only supports English for LCD interface currently.</​note>​
 +
 +<ff sans-serif><​fs medium>​2. Config.Settings.LANGUAGE.WebLang = 0\\ 
 +*Description:​ The web language of device.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0(default) |English|
 +
 +<ff sans-serif><​fs medium>​Website:​ Phone->​Time/​Lang->​Web Language</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c25.png?​nolink |}}\\ 
 +<​note>​NOTE:​ C313/​IT80/​IT81 only supports English for website currently.</​note> ​
 +
 +
 +====Time====
 +
 +<ff sans-serif><​fs medium>​1. Config.Settings.DATETIME.Type = 0\\ 
 +*Description:​ The type of DST</​fs></​ff>​.
 +^Value ^Description^
 +|0 (default) |Date|
 +|1 |Week|
 +
 +
 +<ff sans-serif><​fs medium>​2. Config.Settings.DATETIME.TimeFormat = 0\\ 
 +*Description:​ The format of time.</​fs></​ff>​
 +^Value ^Description^
 +|0 (default) |12 Hour| 
 +|1 |24 Hour|
 +
 +<ff sans-serif><​fs medium>​*Website:​ Phone->​Time/​Lang->​Format Setting</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c26.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​3. Config.Settings.DATETIME.DateFormat = 2\\ 
 +*Description:​ The format of date.</​fs></​ff>​
 +^Value ^Description^
 +|0 |YYYY-MM-DD|
 +|1 |YYYY/​MM/​DD|
 +|2(default) |DD-MM-YYYY|
 +|3 |DD/​MM/​YYYY|
 +|4 |WW-DD-MM|
 +|5 |WW-MM-DD|
 +|others |WW DD/MM/YYYY|
 +<fs medium>​*Website:​ Phone->​Time/​Lang->​Format Setting</​fs>​
 +{{ :​2.indoor_monitor:​feature_guides:​c27.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​4. Config.Settings.DATETIME.Offset = 60\\ 
 +*Description:​ The offset minutes for DST. Range is -300 ~ 300. It will be effective when DST is enabled.\\ ​
 +*Website: Phone->​Time/​Lang->​Daylight Saving Time</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c28.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​5. Config.Settings.DATETIME.ShowStatusBarTime = 1\\ 
 +*Description:​ Show date and time on status bar or not.\\ ​
 +\\
 +6. Config.Settings.SNTP.Enable = 1\\ 
 +*Description:​ Enable/​Disable NTP feature.\\ ​
 +\\
 +7. Config.Settings.SNTP.TimeZone = +1\\ 
 +\\
 +8. Config.Settings.SNTP.Name = France(Paris)\\ ​
 +*Description:​ Time zone and time name for device. The range of time zone is -11 ~ +13.</​fs></​ff>​\\ ​
 +<​note>​NOTE:​The recommended settings in TimeZone.xml.</​note>​
 +
 +<ff sans-serif><​fs medium>​9. Config.Settings.SNTP.NTPServer1 = 0.pool.ntp.org\\ ​
 +\\
 +10. Config.Settings.SNTP.NTPServer2 = 1.pool.ntp.org\\
 +*Description:​ The primary/​secondary NTP server IP or domain name.\\ ​
 +*Website:​Phone->​Time/​Lang->​NTP</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c29.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​11. Config.Settings.SNTP.DTS = 2\\ 
 +*Description:​ The mode of daylight saving time</​fs></​ff>​
 +^Value ^Description^
 +|0 |Disabled|
 +|1 |Enabled, the offset and date would be set by user.|
 +|2(default) |Auto,​ user don't need to set offset and date.|
 +<ff sans-serif><​fs medium>​*Website:​ Phone->​Time/​Lang->​Daylight Saving Time</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c30.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​12. Config.Settings.SNTP.Interval = 3600\\ ​
 +*Description:​ The time updating interval. The range is 3600 ~ 65535.\\ ​
 +Website: Phone->​Time/​Lang->​NTP</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c31.png?​nolink |}}\\ 
 +
 +<ff sans-serif><​fs medium>​13. Config.Settings.SNTP.StartTime = 1/​1/​0\\ ​
 +\\
 +14. Config.Settings.SNTP.EndTime = 12/​31/​23\\ ​
 +*Description:​ The start time and end time for daylight saving time feature. The format is Month/​Day/​Hour. It would be effective when DST mode is "​Enabled"​ and the DST type is "By Date"​.\\ ​
 +*Website: Phone->​Time/​Lang->​Daylight saving time</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c32.png?​nolink |}}\\ 
 +
 +
 +====Backlight====
 +<ff sans-serif><​fs medium>​1. Config.Settings.BACKLIGHT.Level = 5\\ 
 +*Description:​The backlight level of device. The value range is 1~10.\\ ​
 +\\
 +2. Config.Settings.BACKLIGHT.Time = 300\\ 
 +*Description:​The backlight time, it is in seconds. The value range is 1~7200. Recommended value is 15, 30, 60, 120, 300, 600, 1800, 3600, 7200.\\ ​
 +\\
 +3. Config.Settings.BACKLIGHT.FreeLevel = 0\\ 
 +*Description:​The backlight level be set when backlight is off. It supports to use a low level backlight when backlight is off.</​fs></​ff>​\\ ​
 +
 +
 +====Log Level====
 +<ff sans-serif><​fs medium>​1. Config.Settings.LOGLEVEL.Level = 3\\ 
 +*Description:​ The log level of device. The range of log level is 0~7.</​fs></​ff>​
 +^Value ^Description^
 +|0 |EMERGENCY|
 +|1 |ALERT|
 +|2 |CRITICAL|
 +|3(default) |ERROR|
 +|4 |WARNING|
 +|5 |NOTICE|
 +|6 |INFORMATIONAL|
 +|7 |DEBUG|
 +
 +<ff sans-serif><​fs medium>​2. Config.Settings.LOGLEVEL.RemoteSyslog = 0\\ 
 +*Description:​ Enable/​Disable remote syslog feature.\\ ​
 +\\
 +3. Config.Settings.LOGLEVEL.RemoteServer = \\ 
 +*Description:​ The remote syslog server IP or domain name</​fs>​.</​ff>​\\ ​
 +<​note>​NOTE:​ The syslog server port is 514.
 +</​note>​
 +
 +
 +====Ringtone & Volume====
 +<​note>​NOTE:​ The middle volume is the volume level which logic level 8 on. The logic volume level is in range of 1~15. For example, if middle value is 28, the logic volume level 8 is on volume level 36. The middle volume range is 1~58.</​note>​
 +
 +<ff sans-serif><​fs medium>​1. Config.Settings.RINGTONE.Type = Ring1.wav\\ ​
 +*Description:​ The ringtone would be played when call incoming.\\ ​
 +*Website: Phone->​Ringtones->​All Ringtones</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c33.png?​nolink |}}\\ 
 +\\
 +<ff sans-serif><​fs medium>​2. Config.Settings.AUDIO.RingVol = 8\\ 
 +*Description:​ The ringtone volume. The range is 0~15. 0 is for silence.\\ ​
 +\\
 +3. Config.Settings.AUDIO.RingMidVol = 38\\ 
 +*Description:​ The middle volume of ring tone. \\ 
 +\\
 +4. Config.Settings.HANDFREE.SpkVol = 8\\ 
 +*Description:​ The handfree speak volume in a call.</​fs></​ff>​\\ ​
 +<​note>​NOTE:​ C313/​IT80/​IT81 only supports handfree mode in a call.</​note>​
 +
 +<ff sans-serif><​fs medium>​5. Config.Settings.HANDFREE.MicVol = 4\\ 
 +*Description:​ The handfree micphone volume in a call.\\ ​
 +\\
 +6. Config.Settings.HANDFREE.SpkMidValue = 45\\ 
 +*Description:​ The handfree speak middle volume.\\ ​
 +\\
 +7. Config.Settings.HANDFREE.SigToneVol = 8\\ 
 +*Description:​ The handfree signal tone volume. The range is 1~15. \\ 
 +\\
 +8. Config.Settings.HANDFREE.SigToneMidVol = 35\\ 
 +*Description:​ The handfree signal middle volume.\\ ​
 +\\
 +9. Config.Settings.SOUND.TouchPadSoundEnable = 1\\ 
 +*Description:​ Enable/​Disable touchpad sound</​fs>​.</​ff>​\\ ​
 +
 +
 +====Login & Password====
 +<ff sans-serif><​fs medium>​1. Config.Settings.LOGIN.Password=123456\\ ​
 +*Description:​ Login password for advance settings on LCD interface.\\ ​
 +\\
 +2. Config.Settings.WEB_LOGIN.User = admin\\ ​
 +\\
 +3. Config.Settings.WEB_LOGIN.Password=admin\\ ​
 +*Description:​ The primary login user and password for website.\\ ​
 +\\
 +4. Config.Settings.WEB_LOGIN.Type = admin\\ ​
 +*Description:​ The type for primary user. It supports 2 types, admin or user.\\ ​
 +\\
 +5. Config.Settings.WEB_LOGIN.User02 = user\\ ​
 +\\
 +6. Config.Settings.WEB_LOGIN.Password02=user\\ ​
 +*Description:​ The secondary login user and password for website.\\ ​
 +\\
 +7. Config.Settings.WEB_LOGIN.Type02 = user\\ ​
 +*Description:​ The type for secondary user. It supports 2 types, admin or user.\\ ​
 +\\
 +8. Config.Settings.WEB_LOGIN_STATUS.Active = 1\\ 
 +*Description:​ Enable/​Disable the login checking. If this feature is enabled, the login would be forbidden when user try to login with incorrect password many times.\\ ​
 +\\
 +9. Config.Settings.WEB_LOGIN_STATUS.SessionTimeOut = 300\\ 
 +*Description:​ How many seconds the login would be forbidden when user try to login with incorrect password many times. It will be effective when login checking feature is enable.</​fs></​ff>​\\ ​
 +
 +
 +====Call====
 +<ff sans-serif><​fs medium>​10. Config.Settings.GENERAL.DirectIP = 1\\ 
 +*Description:​ Enable/​Disable DIRECT IP Call.\\ ​
 +\\
 +11. Config.Settings.GENERAL.UseStarForIP = 1\\ 
 +*Description:​ Enable/​Disable replacing '​*'​ to '​.'​ when user try to call to an IP address included '​*'​. For example, if this feature is enabled, when user dial "​192*168*1*10",​ it will be transferred to 192.168.0.10.\\ ​
 +\\
 +12. Config.Settings.GENERAL.HungUpBusyTone = 0\\ 
 +*Description:​ Play busy tone when remote party hanged up the call or not.\\ ​
 +*Website: Phone->​Call Feature->​Others
 +{{ :​2.indoor_monitor:​feature_guides:​c34.png?​nolink |}}
 +\\
 +13. Config.Settings.INDICATOR.MissedCall = 1\\ 
 +*Description:​ Enable/​Disable showing the missed call icon on status bar or not when there is missed call.\\ ​
 +\\
 +14. Config.Settings.INDICATOR.Message = 1\\ 
 +*Description:​ Enable/​Disable showing the message icon on status bar or not when there is unread message.\\ ​
 +\\
 +15. Config.Settings.CALLTIMEOUT.DialOut = 60\\ 
 +\\
 +16. Config.Settings.CALLTIMEOUT.DialIn = 60\\ 
 +*Description:​ Call timeout when the remote party not answered. It is in seconds.\\ ​
 +\\
 +17. Config.Settings.E10S_RINGTONE.Type = Ring1.wav\\ ​
 +*Description:​The ring tone would be played when door unit called in.\\ 
 +*Website:​Phone->​Ringtones->​All Ringtones\\ ​
 +{{ :​2.indoor_monitor:​feature_guides:​c35.png?​nolink |}}
 +\\
 +18. Config.Settings. AUTO_ANSWER.IndoorToIndoor=0\\ ​
 +*Description:​ Auto-Answer when other indoor monitor call in.\\ 
 +Website: **Phone->​Call Feature->​Others**</​fs></​ff>​\\ ​
 +{{ :​2.indoor_monitor:​feature_guides:​c36.png?​nolink |}}
 +
 +
 +=== =Programmable Key ====
 +<ff sans-serif><​fs medium>​1. Config.Programable.CENTER.Type = 10\\ 
 +The feature for call center button,</​fs></​ff>​\\
 +^Value ^Description^
 +|10 (default) |Speed dial to the number be set in Config.Programable.CENTER.Param1.|
 +|37 |Call to SDMC system.|
 +<ff sans-serif><​fs medium>​Website:</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c37.png?​nolink |}}\\ 
 +
 +
 +<ff sans-serif><​fs medium>​2. Config.Programable.CENTER.Param1 = \\ 
 +*Description:​ The number would be call to when Config.Programable.CENTER.Type is be set to 10(Speed dial).\\ ​
 +\\
 +3. Config.Programable.CENTER.Param2 = 0\\ 
 +*Description:​ The account be selected for calling out.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Auto|
 +|1~X |Account 1 ~ AccountX|
 +
 +
 +====Monitor====
 +
 +<ff sans-serif><​fs medium>​1. Config.Settings.MONITOR.WithWebcamEntry=0\\ ​
 +*Description:​ Enable/​Disable Webcam feature in device. If this feature is enabled, user will see Webcam feature in the Monitor interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disable|
 +|1 |Enable|
 +
 +<ff sans-serif><​fs medium>​2. Config.Settings.MONITOR.TimeOut=180\\ ​
 +*Description:​ How many seconds the monitoring will be ended automatically.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Timeout is inactivated. Monitoring will not be ended automatically.|
 +|30~65535 |Timeout seconds. Default is 180.|
 +
 +<ff sans-serif><​fs medium>​3. Config.Settings.MONITOR.WithOnvifEntry=0\\ ​
 +*Description:​ Enable/​Disable ONVIF feature in device. If this feature is enabled, user will see ONVIF feature in the Monitor interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disable|
 +|1 |Enable|
 +
 +====Door Bell====
 +<ff sans-serif><​fs medium>​1. Config.Settings.DOORBELL.Enable = 0\\ 
 +*Description:​ Enable/​Disable door bell feature.\\ ​
 +\\
 +2. Config.Settings.DOORBELL.Zone = 1\\ 
 +*Description:​ Which zone would be used for door bell feature. The value range is 1~8.\\ ​
 +\\
 +3. Config.Settings.DOORBELL.Ring = Ring2.wav\\ ​
 +*Description:​ The ring tone for door bell feature. It would be played when some one pressed the button.</​fs></​ff>​\\ ​
 +
 +====Screen Saver====
 +
 +<ff sans-serif><​fs medium>​1. Config.Settings.SCREENSAVER.Enable = 1\\ 
 +*Description:​Enable/​Disable screen saving feature.\\ ​
 +\\
 +2. Config.Settings.SCREENSAVER.Type = 2\\ 
 +*Description:​The type of screen saving.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Using the pictures SDMC sent.|
 +|1 |Using local pictures.|
 +|2(default) |Using local pictures and the pictures SDMC sent.|
 +
 +<ff sans-serif><​fs medium>​3. Config.Settings.SCREENSAVER.Mode = 0\\ 
 +*Description:​The mode of screen saving.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Pictures|
 +|1 |Clock|
 +
 +<ff sans-serif><​fs medium>​4. Config.Settings.SCREENSAVER.StartTime = 00:​00\\ ​
 +*Description:​ The start time of screen saver feature. Default is 00:​00.\\ ​
 +\\
 +5. Config.Settings.SCREENSAVER.EndTime = 23:​59\\ ​
 +Description:​ The end time of screen saver feature. Default is 23:​59.</​fs></​ff>​\\ ​
 +
 +====Others====
 +
 +<ff sans-serif><​fs medium>​1. Config.Settings.GENERAL.WebTitle = IP Phone\\ ​
 +*Description:​ The title would be shown on the tab of browser.\\ ​
 +
 +2. Config.Settings.GENERAL.HttpUserAgent = \\ 
 +*Description:​ The user agent for http downloading.\\ ​
 +
 +3. Config.Settings.homeMode.Mode = 0\\ 
 +*Description:​The arming mode of device</​fs>​.</​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disarming.|
 +|1 |In door arming mode.|
 +|2 |Sleeping arming mode.|
 +|3 |Out door arming mode.|
 +<ff sans-serif><​fs medium>​*Website:​ Arming->​Arming Mode->​Arming Mode</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c38.png?​nolink |}}\\ 
 +
 +
 +
 +<fs medium><​ff sans-serif>​4. Config.Settings.BELLIN.RingTime = 1\\ 
 +*Description:​ The seconds ring tone would played. The value range is 1~10.\\ ​
 +
 +5. Config.Settings.DIAL.WithDialEntry = 1\\ 
 +*Description:​ Enable/​Disable the dial pad feature in dial interface</​ff></​fs>​.\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +|1(default) |Enabled|
 +|2 |Auto, enabled always.|
 +
 +<fs medium><​ff sans-serif>​6. Config.Settings.DIAL.WithDialResidentEntry = 0\\ 
 +*Description:​ Enable/​Disable the dial resident feature in dial interface.</​ff></​fs>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disabled|
 +|1 |Enabled|
 +|2 |Auto, disabled always.|
 +
 +<ff sans-serif><​fs medium>​7. Config.Settings.DIAL.WithDoorPhoneEntry = 2\\ 
 +Description:​ Enable/​Disable the dial resident feature in dial interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +|1 |Enabled|
 +|2(default) |Auto,​ disabled when connecting to AK cloud server, enabled when connecting to SDMC, enabled when device didn't connect to SDMC/AK Cloud.|
 +
 +<ff sans-serif><​fs medium>​8. Config.Settings.DIAL.WithCallCenterEntry = 2\\ 
 +*Description:​ Enable/​Disable the call center feature in dial interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +|1 |Enabled|
 +|2(default) |Auto,​ disabled when connecting to AK cloud server, enabled when connecting to SDMC, enabled when device didn't connect to SDMC/AK Cloud.|
 +
 +<ff sans-serif><​fs medium>​8. Config.Settings.DIAL.WithSpeedDialEntry = 0\\ 
 +*Description:​ Enable/​Disable the speed dial feature in dial interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disabled|
 +|1 |Enabled|
 +|2 |Auto, disabled always.|
 +
 +<ff sans-serif><​fs medium>​9. Config.Settings.DIAL.WithRingGroupEntry = 0\\ 
 +*Description:​ Enable/​Disable the ring group feature in dial interface</​fs>​.</​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disabled|
 +|1 |Enabled|
 +|2 |Auto, disabled always.|
 +
 +<ff sans-serif><​fs medium>​10. Config.Settings.DIAL.WithIndoorExtensionEntry = 0\\ 
 +*Description:​ Enable/​Disable the call indoor feature in dial interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +|1 |Enabled|
 +|2(default) |Auto,​ disabled always.|
 +
 +<ff sans-serif><​fs medium>​11. Config.Settings.CONTACT.WithLocalEntry = 2\\ 
 +*Description:​ Enable/​Disable the local phonebook feature in contact interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +|1 |Enabled|
 +|2(default) |Auto,​ disabled when connecting to AK cloud server, enabled when connecting to SDMC, enabled when device didn't connect to SDMC/AK Cloud.|
 +
 +<ff sans-serif><​fs medium>​12. Config.Settings.CONTACT.WithDeviceEntry = 1\\ 
 +*Description:​ Enable/​Disable the device list in contact interface.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |Disabled|
 +1(default) |Enabled|
 +|2 |Auto, enabled always.|
 +
 +<ff sans-serif><​fs medium>​13. Config.Settings.RELAY.Interval = 3\\ 
 +*Description:​ The time relay would be lasted after be triggered.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |About 400ms|
 +|1~65535 |Seconds.|
 +<ff sans-serif><​fs medium>​*Website:​ Phone->​Relay->​Relay Setting</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c39.png?​nolink |}}\\ 
 +
 +
 +
 +
 +=====Indoor Settings=====
 +====Call & Door Opening====
 +===Non Android Devices===
 +<​note>​NOTE:​ C313/​IT80/​IT81 supports Name1~Name4,​ Number1~Number4.</​note>​\\ ​
 +
 +<ff sans-serif><​fs medium>​1. Config.InDoor. IndoorExtension.Name1=\\ ​
 +\\
 +2. Config.InDoor. IndoorExtension.Number1=\\ ​
 +*Description:​ The indoor extension name and number list, it is for "​Indoor Phone" feature in dial interface.\\ ​
 +\\
 +3. Config.InDoor.CallCenter.CallCenterNumber=\\ ​
 +*Description:​ The number for call center button.\\ ​
 +\\
 +4. Config.InDoor.OpenDoor.Code=#​\\ ​
 +*Description:​ The DTMF code would be sent out for opening the remote door. \\ 
 +*Website: Phone->​Relay->​Relay Setting</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c40.png?​nolink |}}
 +
 +<ff sans-serif><​fs medium>​5. Config.InDoor.OpenLocalDoor.Code=#​\\ ​
 +*Description:​ Open local door when receiving this DTMF code.\\ ​
 +*Website: Phone->​Relay->​Relay Setting</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c41.png?​nolink |}}
 +
 +===Android Devices===
 +<ff sans-serif><​fs medium>​1. Config.Indoor.SOS.SOSNumber = \\ 
 +*Description:​ The call number of SOS.</​fs></​ff>​\\ ​
 +
 +
 +
 +====RTSP====
 +===Non Android Devices===
 +
 +<ff sans-serif><​fs medium>​1. Config.InDoor.RTSP.Enable=1\\ ​
 +\\
 +2. Config.InDoor.RTSP.UserName=\\ ​
 +\\
 +3. Config.InDoor.RTSP.Password=\\ ​
 +*Description:​ The Enabled/​UserName/​Password settings for RTSP server feature.</​fs></​ff>​\\ ​
 +
 +===Android Devices===
 +<ff sans-serif><​fs medium>​1. Config.Settings.RTSPD.RTSPDEnable = 0\\ 
 +*Description:​ Enable/​Disable RTSP server feature</​fs>​.</​ff>​\\ ​
 +
 +====Arming====
 +===Non Android Devices===
 +
 +<​note>​NOTE:​ This arming settings is only for non android devices(C313/​IT80/​IT81). It supports Alarm01 ~ Alarm08. Please see other Settings->​Android Indoor Monitor->​Arming for android devices.</​note>​
 +
 +<ff sans-serif><​fs medium>​1. Config.Arming.Alarm01.Place = Bedroom\\ ​
 +*Description:​ The place for this arming zone.\\ ​
 +*Website: Arming->​Zone Setting->​Zone Setting</​fs></​ff>​
 +{{ :​2.indoor_monitor:​feature_guides:​c42.png?​nolink |}}
 +
 +
 +<ff sans-serif><​fs medium>​2. Config.Arming.Alarm01.Type = Infrared\\ ​
 +Description:​ The type for this arming zone.\\ ​
 +\\
 +3. Config.Arming.Alarm01.Status = 0\\ 
 +*Description:​ The status for this arming zone. If the arming of this zone is enabled, it means that users can</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 (default) |Disable,​ user can't select this zone for any arming mode.|
 +|1 |Enable, user can select this zone for arming mode.|
 +|2 |24 Hour, the alarm would be reported when the sensor be triggered, no matter when device was in arming mode or disarming mode.|
 +
 +<ff sans-serif><​fs medium>​4. Config.Arming.Alarm01.Trigger=1\\ ​
 +*Description:​ NC trigger or NO trigger.</​fs></​ff>​\\ ​
 +^Value ^Description^
 +|0 |NO trigger|
 +|1 (default) |NC trigger|
 +Website: **Arming->​Arming Mode->​Home**
 +{{ :​2.indoor_monitor:​feature_guides:​c43.png?​nolink |}}
 +
 +<ff sans-serif><​fs medium>​5. Config.Arming.Alarm01.Indoor_AlarmDelay = 30\\ 
 +*Description:​ How many seconds the alarm would be reported after sensor was triggered. If the triggering of sensor was disappeared during this time, the alarm would not be reported. Recommend value is 0, 30, 60, 90.</​fs></​ff>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​6. Config.Arming.Alarm01.Indoor_Status = 0\\ 
 +*Description:​ Enable/​Disable the arming of this zone for Indoor mode.</​fs></​ff>​\\ ​
 +\\
 +<ff sans-serif><​fs medium>​7. Config.Arming.Alarm01.Indoor_DefenceDelay = 30\\ 
 +*Description:​ How many seconds the arming would be activated after be set on. Recommend value is 0, 30, 60, 90.\\
 +\\
 +8. Config.Arming.Alarm01.Sleeping_AlarmDelay = 90\\ 
 +\\
 +9. Config.Arming.Alarm01.Sleeping_Status = 0\\ 
 +\\
 +10. Config.Arming.Alarm01.Sleeping_DefenceDelay = 30</​fs></​ff>​\\ ​
 +<​note>​NOTE:​ please see Indoor mode.</​note>​
 +
 +<ff sans-serif><​fs medium>​11. Config.Arming.Alarm01.Outdoor_AlarmDelay = 0\\ 
 +\\
 +12. Config.Arming.Alarm01.Outdoor_Status = 1\\ 
 +\\
 +13. Config.Arming.Alarm01.Outdoor_DefenceDelay = 0</​fs></​ff>​\\ ​
 +<​note>​NOTE:​ please see Indoor mode.</​note>​
 +
 +
 +===Android Devices===
 +<ff sans-serif><​fs medium>​1. Config.HomeSecurity0.Alarm01.Place = Bedroom\\ ​
 +\\
 +2. Config.HomeSecurity0.Alarm01.Type = Infrared\\ ​
 +\\
 +3. Config.HomeSecurity0.Alarm01.Status = 0\\ 
 +\\
 +4. Config.HomeSecurity0.Alarm01.Home_AlarmDelay = 90\\ 
 +\\
 +5. Config.HomeSecurity0.Alarm01.Home_Status = 0\\ 
 +\\
 +6. Config.HomeSecurity0.Alarm01.Home_DefenceDelay = 90\\ 
 +\\
 +7. Config.HomeSecurity0.Alarm01.Night_AlarmDelay = 90\\ 
 +\\
 +8. Config.HomeSecurity0.Alarm01.Night_Status = 0\\ 
 +\\
 +9. Config.HomeSecurity0.Alarm01.Night_DefenceDelay = 90\\ 
 +\\
 +10. Config.HomeSecurity0.Alarm01.Leaving_AlarmDelay = 90\\ 
 +\\
 +11. Config.HomeSecurity0.Alarm01.Leaving_Status = 0\\ 
 +\\
 +12. Config.HomeSecurity0.Alarm01.Leaving_DefenceDelay = 90\\ 
 +\\
 +13. Config.HomeSecurity0.Alarm01.Trigger = 1\\ 
 +\\
 +14. Config.HomeSecurity0.Alarm01.SmsMessage =\\ 
 +\\
 +15. Config.HomeSecurity0.AlarmAsChangingMode.Enable = 0\\ 
 +\\
 +16. Config.HomeSecurity0.AlarmEmergency.CallAddress = \\ 
 +\\
 +17. Config.HomeSecurity0.AlarmEmergency.MessageAddress =</​fs>​
 +</ff> \\
 +
 +====Others====
 +===Android Devices===
 +<ff sans-serif><​fs medium>​1. Config.Indoor.IDLEWEATHER.ShowWeather =</​fs></​ff>​\\ ​
 +
 +====Door Settings====
 +===Device Node===
 +<ff sans-serif><​fs medium>​1. Config.DoorSetting.DEVICENODE.Type=2\\ ​
 +*Description:​ The type of this device.</​fs></​ff>​\\ ​
 +
 +^Value ^Description^
 +|0 |Stair Phone|
 +|1 |Door Phone|
 +|2 (default) |Indoor Monitor|
 +|3 |Management Phone|
 +|4 |Wall Phone|
 +
 +<ff sans-serif><​fs medium>​2. Config.DoorSetting.DEVICENODE.Address=1.1.1.1.1\\ ​
 +*Description:​ The node of this device. 1.2.3.4.5 means Area1, Building2, Unit3, Floor4, Room5.</​fs></​ff>​\\ ​
 +\\
 +<fs medium><​ff sans-serif>​3. Config.DoorSetting.DEVICENODE.Extension=1\\ ​
 +*Description:​ The extension of this device. The value range is 1~9.</​ff>​\\ ​
 +</fs>
 +\\
 +<ff sans-serif><​fs medium>​4. Config.DoorSetting.DEVICENODE.Location=Indoor Monitor\\ ​
 +*Description:​ The location of this device. It also can be the name of this device.</​fs></​ff>​\\ ​
 +
 +
 +
 +====Android Devices====
 +===RELAY===
 +<ff sans-serif><​fs medium>​1. Config.DoorSetting.RELAY.Delay1 = 3\\ 
 +*Description:​ The delay seconds of relay 1, the recommended value is 1~9, 10, 20.\\ 
 +\\
 +2. Config.DoorSetting.RELAY.Delay2 = 3\\ 
 +*Description:​ The delay seconds of relay 2, the recommended value is 1~9, 10, 20.\\ 
 +\\
 +3. Config.DoorSetting.RELAY.DTMFCode = #\\ 
 +*Description:​ The DTMF code for relay 1, it supports multiple DTMF code like 1212#​.\\ ​
 +\\
 +4. Config.DoorSetting.RELAY.ChimeBellEnable = 0\\ 
 +*Description:​ Enable/​Disable chime bell feature.\\ ​
 +\\
 +5. Config.DoorSetting.RELAY.HardkeyRelayType = 0\\ 
 +*Description:​The type of the unlock key in touch panel.\\ ​
 +*Value:</​fs></​ff>​
 +^Value ^Description^
 +|0 (default) |UNLOCK_TYPE_RELAY1|
 +|1 |UNLOCK_TYPE_RELAY2|
 +|2 |UNLOCK_TYPE_DTMF|
 +|3 |UNLOCK_TYPE_HTTP|
 +|4~13 |UNLOCK_TYPE_WEBRELAY_1 ~ UNLOCK_TYPE_WEBRELAY_10|
 +|14 |UNLOCK_TYPE_DTMF_2|
 +|15 |UNLOCK_TYPE_DTMF_3|
 +
 +<ff sans-serif><​fs medium>​6. Config.DoorSetting.RELAY.HardkeyActive = 1\\ 
 +*Description:​Enable/​Disable the unlock key in touch panel.\\ ​
 +\\
 +7. Config.DoorSetting.RELAY.MonitorStatus = 1\\ 
 +*Description:​Enable/​Disable the unlock key in monitor interface.\\ ​
 +\\
 +8. Config.DoorSetting.RELAY.MonitorDisplayName = Unlock\\ ​
 +*Description:​The display name for unlock key in monitor interface.\\ ​
 +\\
 +9. Config.DoorSetting.RELAY.MonitorRelayType = 3\\ 
 +*Description:​The type of unlock key in monitor interface. Please see the type list which described for\\ Config.DoorSetting.RELAY.HardkeyRelayType.\\ ​
 +\\
 +10. Config.DoorSetting.RELAY.TalkingStatus1 = 1\\ 
 +*Description:​ Description:​Enable/​Disable the 1st unlock key in talking interface.\\ ​
 +\\
 +11. Config.DoorSetting.RELAY.TalkingColDisplayName1 = Unlock1\\ ​
 +*Description:​The display name for the 1st unlock key in talking interface.\\ ​
 +\\
 +12. Config.DoorSetting.RELAY.TalkingRelayType1 = 0\\ 
 +*Description:​The type of the 1st unlock key in talking interface. Please see the type list which described for Config.DoorSetting.RELAY.HardkeyRelayType.\\ ​
 +\\
 +13. Config.DoorSetting.RELAY.TalkingStatus2 = 1\\ 
 +*Description:​ Description:​Enable/​Disable the 2nd unlock key in talking interface.\\ ​
 +\\
 +14. Config.DoorSetting.RELAY.TalkingColDisplayName2 = Unlock2\\ ​
 +*Description:​The display name for the 2nd unlock key in talking interface.\\ ​
 +\\
 +15. Config.DoorSetting.RELAY.TalkingRelayType2 = 2\\ 
 +*Description:​The type of the 2nd unlock key in talking interface. Please see the type list which described for\\ Config.DoorSetting.RELAY.HardkeyRelayType.\\
 +\\
 +16. Config.DoorSetting.RELAY.TalkingStatus3 = 1\\ 
 +*Description:​ Description:​Enable/​Disable the 3rd sunlock key in talking interface\\ ​
 +\\
 +17. Config.DoorSetting.RELAY.TalkingColDisplayName3 = Unlock3\\ ​
 +*Description:​The display name for the 3rd unlock key in talking interface.\\ ​
 +\\
 +18. Config.DoorSetting.RELAY.TalkingRelayType3 = 14\\ 
 +*Description:​The type of the 3rd unlock key in talking interface. Please see the type list which described for Config.DoorSetting.RELAY.HardkeyRelayType.\\ ​
 +\\
 +19. Config.DoorSetting.RELAY.LocalRelayType1 = 0\\ 
 +*Description:​ The type of local relay.\\ ​
 +*Value:</​fs></​ff>​
 +^Value ^Description^
 +|0(default) |LOCAL_RELAY_OPEN_DOOR|
 +|1 |LOCAL_RELAY_EXT_SPEAKER|
 +|2 |LOCAL_RELAY_CHIME_BELL|
 +
 +<ff sans-serif><​fs medium>​20. Config.DoorSetting.RELAY.DTMFCode2 = #\\ 
 +*Description:​ The DTMF code for relay 2, it supports multiple DTMF code like 1212#​.\\ ​
 +
 +21. Config.DoorSetting.RELAY.DTMFCode3 = #\\ 
 +*Description:​ The DTMF code for relay 3, it supports multiple DTMF code like 1212#​.</​fs></​ff>​\\ ​
 +
 +===ONVIF===
 +<ff sans-serif><​fs medium>​1. Config.DoorSetting.ONVIF.Mode = 1</​fs></​ff>​\\ ​
 +*Description:​ The mode of ONVIF.\\ ​
 +^Value ^Description^
 +|0 |Discovery mode.|
 +|1(default) |Non discovery mode.|
 +
 +<ff sans-serif><​fs medium>​2. Config.DoorSetting.ONVIF.User = \\ 
 +
 +3. Config.DoorSetting.ONVIF.Pwd =\\ 
 +*Description:​ The user and password for ONVIF feature.</​fs></​ff>​\\ ​
 +
 +