meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
7.ip_phone:features_and_configurations:how_to_setup_snmp [2019/01/23 16:20]
inn
— (current)
Line 1: Line 1:
-====== How to setup SNMP feature ====== 
-=====  1.Introduction ===== 
-<fs medium>​S<​ff sans-serif>​NMP(Simple Network Management Protocol) is an Internet - standard protocol for managing devices on IP networks. Typically, SNMP is widely used in network management system to monitor network - attached devices for conditions that may draw network administrative attention. SNMP exposes management data in the form of variables on the managed systems, which describe the system configuration. These variables can then be queried by managing applications. The variablesaccessible via SNMP are organized in hierarchies,​ which are described by Management Information Bases (MIBs</​ff>​)</​fs> ​ 
- 
-===== 2.Configure SNMP on Akuvox phone ===== 
-<fs medium><​ff sans-serif>​1. Login the phone’s web page, go to Network - Advanced. \\ 
-\\ 
-2. Enable SNMP from drop-down list. \\ 
-\\ 
-3. Input the port number, IP address of trusted SNMP server as below.</​ff></​fs>​ \\  
-{{ :​7.ip_phone:​features_and_configurations:​snmp.png?​nolink&​400 |}} 
- 
-===== 3.Basic object identifiers ===== 
-<fs medium><​ff sans-serif>​The following table shows some basic object identifiers supported by akuvox phone</​ff></​fs>​ 
-^ Name ^ OID ^ Type ^ Execute SecureCRT to obtain corelated data ^ 
-| sysDescr | 1.3.6.1.2.1.1.1 | DisplayString |Run uname –a (eg.Linux (none) 2.6.10_dev-malta-mips2_fp_len #44 Sun Jun 1602:33:13 PDT 2013 mips ) | 
-| sysUpTime | 1.3.6.1.2.1.1.3 | TIMETICKS | | 
-| sysContact | 1.3.6.1.2.1.1.4 | OctetString |R52 version must be:Sysadmin (root@localhost) | 
-| sysLocation | 1.3.6.1.2.1.1.6 | OctetString |R52 version must be:Server Room | 
-| ifNumber | 1.3.6.1.2.1.2.1 | Integer |Run ifconfig to check the number of interface(eg. 3) \\ Note:One of them is hidden interface | 
-| ifDescr | 1.3.6.1.2.1.2.2.1.2 | OctetString |Run Ifconfig(eg. Esw0,​lo,​teql0 )  \\ Note:teql0 is hidden interface | 
-| ifType | 1.3.6.1.2.1.2.2.1.3 | Integer |Run Ifconfig to check the encap parameter of two interfaces(eg. Esw0: Ethernet;​lo:​ Local Loopback) | 
-| ifMtu | 1.3.6.1.2.1.2.2.1.4 | Integer |Run Ifconfig to check MTU parameter of two interfaces | 
-| ifSpeed | 1.3.6.1.2.1.2.2.1.5 | Gauge |Run Ifconfig to check txqueuelen parameter of two interfaces(eg.esw0:​10000000) \\ Note:CRT uses M as units of measurement,​tool uses KB as units of measurement. | 
-| ifPhysAddress | 1.3.6.1.2.1.2.2.1.6 | PHYSADDRESS |Run Ifconfig to check the HWaddr parameter of two interfaces | 
-| ifOperStatus | 1.3.6.1.2.1.2.2.1.8 | Integer | ​ Ifconfig | 
-| ifInOctets | 1.3.6.1.2.1.2.2.1.10 | Counter32 | Ifconfig | 
-| ifInUcastPkts | 1.3.6.1.2.1.2.2.1.11 | Counter32 | Ifconfig | 
-| ifInDiscards | 1.3.6.1.2.1.2.2.1.13 | Counter32 | Ifconfig | 
-| ifInErrors | 1.3.6.1.2.1.2.2.1.14 | Counter32 | Ifconfig | 
- 
-===== 4.Usage of MIB browser ===== 
-<fs medium><​ff sans-serif>​After finish configuring Akuvox IP phone, you can test SNMP feature with MIB( Management Information Base ) Browser tool.</​ff></​fs> ​ 
-<fs medium><​ff sans-serif>​1. Open MIB browser tool</​ff></​fs> ​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp1.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​2. Firstly, fill in the Host IP address and Port number.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp2.png?​nolink&​400 |}} 
-<note tip>Host IP address is related to phone’s IP address, the port number should be the same as the SNMP port number specified on Phone’s web page(Network -> Advanced). </​note>​ 
-<fs medium><​ff sans-serif>​3. Click {{:​7.ip_phone:​features_and_configurations:​snmp20.png|}} and enter following interface.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp4.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​4.Select SNMP version. Akuvox phone support SNMPv1 or SNMPv2.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp5.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​5. Keep other setting as default. \\ 
-\\ 
-6. After finish setting, press [OK] to save. \\  
-\\ 
-7. If IP phone is connected, the following information be displayed.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp6.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​8. After SNMP is enabled, the phone information can be found on MG-SOFT MIB Browser.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp7.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​9. Press {{:​7.ip_phone:​features_and_configurations:​snmp21.png|}} to unfold the tree-like data structure.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp8.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​10. Select{{:​7.ip_phone:​features_and_configurations:​snmp22.png|}} Click right key then choose GET or click {{:​7.ip_phone:​features_and_configurations:​snmp23.png|}} to get the related information for the item.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp9.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​11.Select {{:​7.ip_phone:​features_and_configurations:​snmp22.png|}} Click right key then choose SNMPWALK to get the following information in system directory as below.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp11.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​12. Select {{:​7.ip_phone:​features_and_configurations:​snmp22.png|}} Click right key then choose GETNEXT or click {{:​7.ip_phone:​features_and_configurations:​snmp23.png|}} ​ to get the information of next item</​ff>​.</​fs> ​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp12.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​13. Click **GETBULK SNMP** Data to get the information of all items.</​ff></​fs> ​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp13.png?​nolink&​400 |}} 
-<fs medium><​ff sans-serif>​14. Input OID in below area to obtain the corresponded information.</​ff></​fs>​ 
-{{ :​7.ip_phone:​features_and_configurations:​snmp15.png?​nolink&​400 |}} 
-